Global Manufacturing Partner
Process Comparison

Die Casting vs Machined Aluminum - Cost Guide

Compare die casting vs machined aluminum from billet: tooling cost, unit economics, geometry, mechanical properties, and the volume crossover point.

Mike Yao

Mike Yao

Technical Director, Die Casting Engineering

2026-07-243 min read

Blog Visual Plan

Article visuals for die casting vs machined aluminum

These visuals use your current KastMfg image library now, and they will automatically switch to article-specific images when you add them later.

Die Casting vs Machined Aluminum - Cost G... - Lead Technical Image

Lead Technical Image

Add a hero-level manufacturing, tooling, or component image that reinforces the article topic above the body copy.

Die Casting vs Machined Aluminum - Cost G... - Comparison or Detail Image

Comparison or Detail Image

Reserve a second image for an alloy comparison, defect example, tooling detail, or application close-up deeper in the article.

Engineers face a genuine process choice between die casting and CNC machining for medium-complexity aluminum parts. Both produce precise aluminum components, but their economics diverge sharply as volume changes.


Process Overview

Die Casting: Molten A380/ADC12 injected into hardened steel die. 30-120 second cycle time. Tooling cost $5,000-80,000; material utilization 70-95%; per-unit cost at volume is very low.

CNC Machining: Billet of 6061-T6 or 7075-T6 clamped in machining center; material removed by cutting tools. No tooling cost (fixtures only); material utilization 20-30%; per-unit cost is high but volume-independent.


Full Comparison

Parameter Die Casting CNC Machining
Tooling cost $5,000-80,000 $0-5,000 (fixtures)
Unit cost at 100 pieces High Competitive
Unit cost at 10,000 pieces Very low Much higher
Unit cost at 100,000 pieces Extremely low Prohibitive
Material utilization 70-95% 20-30%
Geometric complexity High (slides for undercuts) Very high (5-axis, few limits)
Min wall thickness 1.2 mm (Al) 0.3-0.5 mm
Dimensional tolerance CT4-CT6 as-cast; +/-0.02 mm machined +/-0.005-0.05 mm
Surface finish Ra 1.6-3.2 μm as-cast Ra 0.4-0.6 μm
First article lead time 5-8 weeks (tooling first) 1-2 weeks
Alloys available A380, ADC12, A360, A413 6061, 7075, 2024, any wrought
Mechanical properties A380: 317 MPa tensile 6061-T6: 310 MPa; 7075-T6: 503 MPa

The Volume Crossover Point

Example calculation:

  • Die casting tooling: $15,000; unit cost: $3.50
  • CNC machining tooling: $0; unit cost: $18.00
  • Crossover: $15,000 / ($18.00 -$3.50) = 1,034 pieces

Above ~1,000 pieces total, die casting is more economical. At 10,000 pieces, die casting saves $145,000 versus machining. In practice the crossover falls between 500 and 5,000 pieces depending on part complexity.


When to Choose CNC Machining

  • Volume under 1,000 units lifetime: Avoid tooling investment
  • Wrought alloy properties required: 7075-T6 (503 MPa) and 2024-T3 cannot be die cast
  • Complex internal passages: Multi-axis or EDM produces tortuous passages die casting cannot form
  • Short development timeline: Machined first articles in 1-2 weeks vs 5-8 weeks for die casting
  • Very tight tolerances on nearly all features: If +/-0.01 mm applies everywhere, machining may be more economical than extensive post-cast machining

When to Choose Die Casting

  • Production volumes above 2,000-5,000 pieces
  • Complex geometry with thin walls, fins, integrated bosses: Economical in die casting; expensive in machining
  • Integrated thermal management: Fin arrays, cooling channels impossible to machine economically
  • Single-source finished component: Casting + machining + finishing on one PO

Prototype-to-Production Transition

Most products begin as machined prototypes and transition to die casting for production. Managing this well:

  1. Design for both: Keep draft angle requirements and parting line placement in mind during prototype design
  2. Use cast prototypes before production tooling: 50-500 pieces from P20 soft tooling validates casting behavior before H13 production tooling commitment
  3. Expect dimensional differences: Cast and machined prototypes of the same design have different as-formed characteristics — evaluate cast prototypes against the drawing, not against the machined prototype

Process selection consultation: casting@kastdiecast.com | +86 138 1403 4409

Mike Yao

About The Author

Mike Yao on die casting vs machined aluminum

Technical Director, Die Casting Engineering

Technical Director at KastMfg with 20+ years in high-pressure die casting, leading engineering and program management across aluminum, zinc, and magnesium programs for automotive, EV, electronics, and medical OEMs worldwide.

View author profile

Related Reading

Keep exploring the blog